You are currently viewing Furnace Clicking or Won’t Turn On: Causes, Safe Checks and Cost

Furnace Clicking or Won’t Turn On: Causes, Safe Checks and Cost

A furnace that clicks and won’t light, on the first cold night of the year, is stressful, and you’re probably wondering what it’ll cost. Here’s what’s going on inside and what you can safely check.

Henley’s says (quick answer): If your furnace won’t turn on at all, start with the thermostat batteries, the furnace power switch and the breaker. If it clicks but never lights, the furnace is trying to start and something in the ignition sequence is failing, often the igniter, flame sensor or a safety switch. Don’t keep resetting it. Have it diagnosed.

En resumen: Si el calentador hace clic pero no enciende, revise el termostato, el interruptor y el breaker. Si sigue sin prender, no lo reinicie muchas veces y llame. El diagnóstico cuesta $59 en llamadas de reparación y no se cobra si aprueba la reparación.

What it usually means

  • Nothing happens at all: dead thermostat batteries, the thermostat isn’t set to HEAT, the furnace power switch is off, a tripped breaker, or an open furnace door safety switch.
  • Clicking, but no flame: a modern furnace runs a startup sequence (draft fan, igniter, gas valve, flame check). Repeated clicking without ignition usually points to a worn hot-surface igniter, a dirty flame sensor, a pressure switch problem, or a gas supply issue.
  • Lights for a few seconds, then shuts off: often a dirty flame sensor. The furnace can’t confirm the flame, so it shuts the gas off for safety.
  • Tries a few times, then stops: many furnaces lock out after several failed tries. That’s a safety feature, not something to override.
  • A flashing status light: most furnaces show an error code through a small window in the panel. Write down the flash pattern for the technician.

Is it safe to wait?

It’s OK to try the basic checks below. But don’t keep resetting a furnace that clicks without lighting. Repeated tries can let unburned gas build up, and the furnace locks out for a reason. If anyone at home is vulnerable to the cold, use a safe space heater (follow its instructions) and call.

Checklist: what’s safe to check yourself

  • Check the thermostat. Make sure it’s set to HEAT, the temperature is a few degrees above room temperature, and the batteries are fresh.
  • Check the furnace switch and breaker. Turn on the switch near the furnace (it looks like a light switch) and check for a tripped breaker. Reset a tripped breaker once only.
  • Close the furnace door. Make sure the front panel is fully seated. Many furnaces won’t start with it loose.
  • Replace a clogged filter. A badly clogged filter can make the furnace overheat and shut down.
  • Note the status light. Look through the small window on the furnace panel and write down any flashing code to tell the technician.

Don’t keep cycling the power to force restarts, don’t try to light the burners by hand on a modern furnace, and don’t bypass switches.

When to stop and call

Turn the heat off at the thermostat and call a technician if:

  • It clicks repeatedly without lighting, or lights and shuts off
  • The breaker trips again after one reset
  • You hear a loud bang or boom when it tries to light
  • There’s a burning, electrical or exhaust smell
  • It still won’t start after the checks above

If you smell gas (rotten eggs) or your carbon monoxide alarm goes off: leave the house, then call the gas company or 911. Don’t flip switches, light anything or use your phone until you’re outside, and don’t go back in until responders say it’s safe.

How to prevent it next time

  • Replace the filter regularly so the furnace doesn’t overheat and lock out.
  • Test the heat in early fall, before you need it.
  • Keep fresh batteries in the thermostat.
  • A $99 furnace tune-up cleans the flame sensor and checks the igniter, the two most common reasons for a no-start.

What it costs to fix a furnace that won’t turn on

Henley’s repair calls carry a $59 HVAC diagnostic, waived if you approve the repair. The technician finds the cause (commonly the igniter, flame sensor, pressure switch, control board or thermostat) and gives you the repair price before any work starts. The final cost depends on the part and the furnace, so be wary of anyone quoting a repair price over the phone without seeing it.

Henley’s has been family-owned since 1983. Bryan Henley started it, and owner Billy Henley runs it today. We still do the trade the way it’s supposed to be done: an honest diagnosis, no upsell pressure, the aim of fixing it right the first time, and treating your home like it’s ours.

Neighbors have left 300+ Google reviews for our Corona location. Licensed local technicians, CA Lic. #776658, serving Riverside, San Bernardino and Orange counties.

Call (909) 883-8827 or request service. Repair calls carry a $59 HVAC diagnostic, waived if you approve the repair, and you get the price before any work starts. A $99 furnace tune-up before the cold sets in is the easiest way to head off most of these problems.

¿Prefiere español? Llame al (909) 883-8827 y pida hablar en español. Prefer Spanish? Ask when you call, and we’ll get someone who speaks Spanish on the line.

Related: Heating repair | Furnace tune-up | Furnace blowing cold air? | Thermostat problems | Furnace banging or squealing

Serving Riverside, San Bernardino and Orange counties. Riverside County: Corona, Riverside, Norco, Eastvale, Jurupa Valley, Moreno Valley. San Bernardino County: San Bernardino, Fontana, Rancho Cucamonga, Ontario, Redlands, Rialto, Upland. Orange County: Yorba Linda, Orange.

Frequently asked questions

Why is my furnace clicking but won’t turn on, and what does it cost to fix?
If your furnace won’t turn on at all, start with the thermostat batteries, the furnace power switch and the breaker. If it clicks but never lights, the furnace is trying to start and something in the ignition sequence is failing, often the igniter, flame sensor or a safety switch. Don’t keep resetting it. Have it diagnosed.

Is it safe to wait?
Try the basic checks once, but don’t keep resetting a furnace that clicks without lighting. Repeated tries can let gas build up. Call for a diagnosis.

Why is my furnace clicking but not turning on?
The furnace is trying to start, but a step in the ignition sequence is failing. Common causes are a worn igniter, a dirty flame sensor, a pressure switch problem or a gas supply issue. After a few failed tries it may lock out for safety. Call for a diagnosis rather than resetting it repeatedly.

What should I check first if my furnace won’t turn on?
Thermostat set to HEAT with fresh batteries, the furnace power switch on, the breaker not tripped, the furnace door closed, and a clean filter.

How much does it cost to fix a furnace that won’t turn on in Corona?
Henley’s repair calls carry a $59 HVAC diagnostic, waived if you approve the repair. The repair price depends on the cause and is given to you before any work begins.

Is it safe to keep resetting my furnace?
No. Repeated resets can let unburned gas build up if the ignition is failing. Reset the breaker once at most, then call.

Why does my furnace light and then shut off after a few seconds?
Often the flame sensor is dirty and can’t confirm the flame, so the furnace shuts the gas off for safety. A technician can clean or replace it.